Handle and latch in one—now with ROKR technology. The RV-Labs® Pull-Lock 42mm Flat keeps your camper’s drawers and flaps closed without the need for a separate latch. Rest your knuckle on the handle, tilt it, pull—and it’s open. When you close it, it clicks audibly into place and stays shut, even on bumpy roads.
What Makes ROKR Technology Special
- Positive locking: The handle automatically clicks into place when closed—no accidental opening while driving.
- Open with your ankle: Tilt, then pull. Works even with full hands and without fingernails.
- Smooth-running and durable: The mechanism is designed to withstand many thousands of operations without wearing out or jamming.
- Patented and minimalist: A flat, flush design with no protruding levers—nothing to snag on in narrow passages.
Which Pull-Lock is right for you?
- 42mm flat (this one): flat, straight grip surface. The all-rounder for drawers, kitchen cabinet fronts, and flaps. The most unobtrusive option if you want a clean, minimalist front.
- 42mm half-moon: same width, but with a rounded grip. Choose this one if you prefer a little more room for your fingers.
- 100mm: same technology, three times as wide. For wide kitchen pull-outs and heavy drawers where you want to pull them out perfectly centered.
Technically, all three are the same—the choice comes down purely to aesthetics and usability. Mixing styles looks cluttered: pick one shape and stick with it throughout the entire installation.
Where to use it
- Kitchen drawers and base cabinets in campers, RVs, and travel trailers
- Wall cabinets and flaps above the seating area
- Storage bins, rear garage, and bench flaps
- Boats, workshop carts, and trailers
- At home in the kitchen—the lock also acts as a small barrier for toddlers
Installation
The handle is screwed onto the front from the outside; the counterpart is attached to the fixed cabinet body or under the countertop.
- To install the counterpart, drill a 9mm-deep hole using a 32mm Forstner bit—so be sure to mark the spot accurately and use a depth stop.
- Leave at least a 3mm gap between the front panels so the handle can tilt freely and doesn’t bump into the adjacent panel.
- Choose screws that match the front panel’s thickness—it’s better to go a tad shorter than to let them go all the way through the front panel.
- Before permanently securing the screws, test-fit one front panel and test the opening and closing motion. Then you can mark all the others exactly the same way.
At a Glance
- Handle and latch in a single component
- Width: 42 mm, flat design
- Colors: stainless steel, black, white, and now brushed brass
- ROKR technology: locks into place automatically when closing
- Mating part hole: 32 mm, 9 mm deep
- Minimum gap between cabinet fronts: 3 mm
- Mating piece included
- Price per piece
Frequently Asked Questions
Do I need an additional latch or snap fastener?
No. The Pull-Lock serves as both a handle and a latch—one component per front panel, and you’re all set.
Will it really hold up on rough roads?
Yes, that’s what it’s built for. It locks into place mechanically when closed and only opens when you deliberately tilt the handle.
Does the handle fit any front panel thickness?
It fits standard furniture panels used in camper conversions. If you’re working with very thin or very thick front panels, just reach out to us—we’ll take a look at it with you.
Can I mix colors?
Sure—technically, everything is identical. Visually, you’re usually better off sticking to one color consistently and varying only the size.
How many do I need?
One per drawer or door. For very wide fronts—60 cm or more—two handles are more comfortable; that way, the front won’t pull crooked.
What about the older Pull-Locks in my cabinetry?
The 42-mm width remains the same, but the mechanism is new. If you want to retrofit, send us a photo of your existing handles—we’ll let you know if you can replace them one-to-one or if you’ll need to drill new holes.